313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity pthxx010y 3.3/5/12 vin single output special features ? vtt bus termination output (output the system vref) ? 15 a output current ? 3.3, 5 or 12 vdc input voltage ? ddr and qdr compatible ? on/off inhibit (for vtt standby) ? under-voltage lockout ? operating temperature range: -40 c to +85 c ? effciencies up to 91% ? output overcurrent protection (non-latching, auto-reset) ? point-of-load-alliance (pola) compatible ? available rohs compliant ? 2 year warranty total power: 27w # of outputs: single safety ul/cul can/csa-c22.2 no. 60950, file no. e174104 tv product service (en60950) certifcate no. b 04 06 38572 044 cb report and certifcate to iec60950, certifcate no. us/8292/ul ? ? ? rev.2.16.09_147 pthxx010y 1 of 5 input input voltage range: pth03010y pth05010y PTH12010Y 2.95 - 3.65 vdc 4.5 - 5.5 vdc 10.8 - 13.2 vdc input current: no load 10 ma remote on/off: positive logic undervoltage lockout: pth03010y vin increasing vin decreasing 2.45 v typ., 2.80 v max. 2.20 v min., 2.40 v typ. pth05010y vin increasing vin decreasing 4.30 v typ., 4.45 v max. 3.40 v min., 3.70 v typ. PTH12010Y vin increasing vin decreasing 9.5 v typ., 10.4 v max. 8.80 v min., 9.0 v typ. input capacitance: (see note 3) pth03010y & pth05010y PTH12010Y 470 f 560 f specifcations all specifcations are typical at nominal input, v ref = 1.25 v, full load at 25?c unless otherwise stated. c in , c o1 and c o2 = typical value
rev.2.16.09_147 pthxx010y 2 of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 output output current: (over v v ref range) (see note 1) pth03010y and pth05010y PTH12010Y 15 a 12 a tracking range for v ref : 0.55 - 1.8 vdc tracking tolderance to v ref (v tt - v ref ) (over line, load & temperature) -10 mv to + 10 mv ripple and noise: 20 mhz bandwidth 20 mv pk-pk load transient response: (see note 4) 30 s settling time s settling time overshoot/undershoot 30 mv typ. output capacitance: non-ceramic values (see notes 4 & 5) pth03010y pth05010y PTH12010Y 470 f typ., 8,200 f max. f typ., 8,200 f max. 470 f typ., 8,200 f max. f typ., 8,200 f max. 940 f typ., 6,600 f max. f typ., 6,600 f max. ceramic values (see note 4) pth03010y pth05010y PTH12010Y 200 f typ., 300 f max. f typ., 300 f max. 200 f typ., 300 f max. f typ., 300 f max. 400 f typ., 600 f max. f typ., 600 f max. (see note 6) esr (non-ceramic) 4 m min. general specifcations effciency: lo = 10 a pth03010y pth05010y PTH12010Y 88% typ. 88% typ. 85% typ. insulation voltage: non-isolated switching frequency: pth03010y pth05010y PTH12010Y 300 - 400 khz 300 - 400 khz 200 - 300 khz approvals and standards (pending): en60950 ul/cul60950 material fammability: ul94v-0 dimensions: (l x w x h) 34.80 x 15.75 x 9.00 mm 1.370 x 0.620 x 0.354 in weight: 3.7 g (0.13 oz) mtbf telcordia sr-332 6,000,000 hours environmental specifcations thermal performance: (see note 2) operating ambient, temperature non-operating -40 c to +85 c -40 c to +125 c msl (z suffx only): jedec j-std-020c level 3 protection overcurrent threshold (auto reset): pth03010y and pth05010y PTH12010Y 27.5 a typ. 20.0 a typ.
rev.2.16.09_147 pthxx010y of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 p t h 0 5 0 1 0 y a s t part number system with options product family point of load alliance compatible mounting option (8) d = horizontal through-hole (matte sn) h = horizontal through-hole (sn/pb) s = surface-mount (63/37 sn/pb pin solder material) z = surface-mount (96.5/3.0/0.5 sn/ag/cu pin solder material) output current 01 = 15 a packaging options no suffx = trays t = tape and reel (7) input voltage 03 = 3.3 v, 05 = 5 v and 12 = 12 v mechanical package always 0 pin option a = through-hole std. pin length (0.140) a = surface-mount tin/lead solder ball output voltage code y = ddr module ordering information output power (max) input voltage v tt range output currents effciency (max) m odel numbers odel numbers (8, 9) min max 27 w 2.95 - 3.65 vdc 0.55 - 1.8 vdc 0 a 15 a 88% pth03010y 27 w 4.5 - 5.5 vdc 0.55 - 1.8 vdc 0 a 15 a 88% pth05010y 21.6 w 10.8 - 13.2 vdc 0.55 - 1.8 vdc 0 a 12 a 85% PTH12010Y notes 1 rating is conditional on the module being soldered to a 4 layer pcb with 1 oz. copper. see the soa curves or contact the factory for appropriate derating. 2 this control pin has an internal pull-up to the input voltage vin. if it is left open-circuit the module will operate when input power is applied. a small low-leakage (<100 na) mosfet is recommended for control. for further information, consult application note 177. 3 an input capacitor is required for proper operation. the capacitor must be rated for a minimum of 800 ma rms of ripple current. 4 the typical value of external output capacitance value ensures that v tt meets the specifed transient performance requirements for the memory bus terminations. lower values of capacitance may be possible when the measured peak change in output current is consistently less than 3 a. test conditions were 15 a/s load step, -1.5 a to +1.5 a. 5 this is the calculated maximum. the minimum esr limitation will often result in a lower value. consult application note 177 for further details. 6 this is the typical esr for all the electrolytic (non-ceramic) output capacitance. use 7 m as the minimum when using max-esr values to calculate. 7 tape and reel packaging only available on the surface-mount versions. 8 to order pb-free (rohs compatible) surface-mount parts replace the mounting option s with z, e.g. pthxx010yaz. to order pb- free (rohs compatible) through-hole parts replace the mounting option h with d, e.g. pthxx010yad. 9 notice: some models do not support all options. please contact your local emerson network power representative or use the on-line model number search tool at http://www.powerconversion.com to fnd a suitable alternative.
rev.2.16.09_147 pthxx010y 4 of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 pthxx010y characteristic data efficienc y (%) 3.3v 5.0v 12.0v 50 60 70 80 90 100 0 3 6 9 12 15 vi n output current (a) nat conv 100 lfm 200 lfm 0 2 4 6 8 10 12 14 16 0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 80 output current (a) ambient tempera ture (oc) figure 3 - efficiency vs load current v ref = 1.25 v (see note b) figure 1 - safe operating area vin = 3.3 v, v ref = 1.25 v, iout = 15 a (see note a) q 1 bss 138 (o pt ion al) 1 k 1 k 1 % 1 % ss tl -2 da ta / address/ bu s v tt te rmin ation islan d gn d v in st andb y v ddq c in (r equired) pthxx010y (t op view) co 1 lo w- es r (r equired) co 2 cerami c (o pt ion al) co n hf -c er amic v tt v ref 4 5 1 2 3 6 7 + 8 9 10 + figure 4 - standard application output current (a) nat conv 100 lfm 200 lfm ambient tempera ture (oc) 0 2 4 6 8 10 12 0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 80 14 figure 2 - safe operating area vin = 12 v, v ref = 1.25 v, iout = 12 a (see note a) notes a soa curves represent the conditions at which internal components are within the emerson network power derating guidelines. b characteristic data has been developed from actual products tested at 25 c. this data is considered typical data for the converter.
rev.2.16.09_147 pthxx010y 5 of 5 0.070 (1.78) (s tando ff should er ) lowe st component 0.010 min. (0.25) bo ttom side cl ea ranc e to p vi ew si de vi ew 1.370 (34.80) 0.620 6 7 3 5 4 10 9 8 1 2 max . 0.354 (9.00) ho st boar d (15.75) ? 0.040 (1.02) 5 pl ac es 0.375 (9.52) 0.125 (3.18) 0.625 (15.88) 0.125 (3.18) (1.52) 0.060 (12.70) 0.500 (1.52) 0.060 (3.55) 0.140 dime nsions in inches (mm) t ole ranc es (unless othe rw ise specified) 2 pl ac es 0.030 ( 0.76) 3 pl ac es 0.010 ( 0.25) to p vi ew 1.370 (34.80) 0.620 6 7 3 5 4 10 9 8 1 2 (15.75) 0.375 (9.52) 0.125 (3.18) 0.625 (15.88) 0.125 (3.18) (1.52) 0.060 (12.70) 0.500 (1.52) 0.060 dime nsions in inches (mm) t ole ran ce s (unless o the r wise specified ) 2 p lace s 0.030 ( 0.76) 3 p lace s 0.010 ( 0.25) ho st boar d lowe st c ompone nt 0.010 min. (0.25) bo ttom side cl ea ranc e si de vi ew solde r ball ? 0.040 (1.02) 10 p lace s *a ft er solde r r ef lo w on c us tomer boar d 0.354 (9.00) ma x. * figure 5 - plated through-hole figure 6 - surface-mount mechanical drawings 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity pin connections pin no. function pin 1 ground pin 2 vin pin 3 inhibit* pin 4 n/c pin 5 vo sense pin connections cont. pin no. function pin 6 v tt pin 7 ground pin 8 v ref pin 9 n/c pin 10 n/c americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.com techsupport.embeddedpower @emerson.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2008 emerson electric co. emersonnetworkpower.com embedded computing embedded power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection emerson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power *denotes negative logic: open = normal operation ground = function active
|
